506_0_3
Anzeige
Topthema: STUDIOART S100 – WEIHNACHTSAKTION
STUDIOART S100 zum Aktionspreis €/CHF 755,- ( anstatt €/CHF 1.595,-)
Als ideales Geschenk für die Familie, liebe Freunde oder sich selbst – entscheiden Sie sich jetzt für die Revox S100 Audiobar.
>> jetzt bis 31.01.2025>> Alle anzeigen
502_23688_2
Topthema: Himmlisches Team
Dynaudio Contour 20i, MOON Audio 250i V2
Unser Hobby spiegelt die Welt da draußen wider: immer mehr, immer größer, immer teurer muss es sein. Zum Glück gibt es aber auch Gegenbeispiele. Mit dem dänischkanadischen Traumduo kann man seinen irdischen Musikfrieden finden.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Quested Monitoring Systems V3110
Ausstattung & technische Daten
| TECHNICAL SPECIFICATION | |
| Dimensions | 380 x 600 x 360mm (w x h x d) |
| Weight | 39kg / 86lb |
| Drivers | Low Frequency 1 x 250mm(10″) |
| Mid | 1 x 75mm (3”) soft dome |
| High Frequency | soft dome 1 x 28mm (1 1/8″) |
| Maximum SPL | 115.5 dB continuous pink noise @ 1m Leq 1 minute. 121.5 dB continuous pink noise per pair @ 1m Leq 1 minute |
| Frequency Response | 34Hz – 20kHz ±2dB / 30Hz – 22kHz -6 dB |
| INPUT | |
| Connector | XLR3 type-Female |
| Impedance | 10k Electronically balanced with RF filters |
| Wiring | Pin 1 ground, Pin 2 hot, Pin 3 cold |
| Sensitivity | Rear mounted 10 position rotary switch calibrated in 2dB steps |
| Minimum sensitivity | +4dBu for 100dB SPL @ 1m |
| Maximum sensitivity | -14dBu for 100 dB SPL @ 1m |
| FILTERS | |
| Subsonic | -3dB @ 14Hz, 24dB/oct |
| Crossover Point | 650Hz, 2k5H, 24dB/oct. |
| User LF EQ | 4 position rear mounted selector to select FLAT for normal use. -9dB and -3dB for cut below 100Hz, +1dB for lift above 80Hz. |
| User MF EQ | 3 position rear mounted switch to select FLAT for normal use, CUT/LIFT +/-1dB for 650Hz to 2k5Hz. |
| User HF EQ | 3 position rear mounted switch to select FLAT for normal use, CUT/LIFT +/-1dB for 2k5Hz to 40kHz. |
| POWER AMPLIFIER | |
| LF output power | > 700W rms continuous (Note 1) |
| Mid Output | > 150W rms continuous (Note 1) |
| HF output power | > 150W rms continuous (Note 1) |
| THD | < 0.03% at levels up to 1dB below clip, 20Hz – 20kHz. typ 0.005% @ 20W rms 1kHz. |
| Hum & Noise | > -100dB referred to clip |
| Note | The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier rear panel and ambient temperatures is <30 o C |
| INDICATION | |
| Power on | Front mounted LED (flashing blue) indicates power applied and warm-up cycle. |
| Optimum Performance | Front mounted LED lights constant blue. |
| Overload | Front mounted LED flashes red 0.5dB below signal clip. |
| Thermal Protection | Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when amplifier temperature drops by 20 o C. |
| POWER REQUIREMENTS | |
| Voltage | Set by internal plugs: nominal 115V or 230V @ 50-60Hz AC. |
| 230V setting | Min 160V (restricted output power): Max 263V |
| 115V setting | Min 80V (restricted output power): Max 132V |
| CONSUMPTION | |
| Quiescent | 72W, typical use 110W. |
| Note | 0dBu = 775mV into open circuit. |
