488_23522_2
Topthema: Ingenieurskunst in Perfektion
Revelation RX2 PRO – High-End Zweikanalendstufe von Brax
Mit der RX2 PRO kündigt Brax nicht weniger als die Endstufe der Superlative an, vollgepackt mit Innovation und das erste Class-D Design der Marke.
>> Mehr erfahren>> Alle anzeigen
502_23688_2
Topthema: Himmlisches Team
Dynaudio Contour 20i, MOON Audio 250i V2
Unser Hobby spiegelt die Welt da draußen wider: immer mehr, immer größer, immer teurer muss es sein. Zum Glück gibt es aber auch Gegenbeispiele. Mit dem dänischkanadischen Traumduo kann man seinen irdischen Musikfrieden finden.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Quested Monitoring Systems S8R
Ausstattung & technische Daten
| TECHNICAL SPECIFICATION | |
| Dimensions | 300(w) x 428(h) x 334(d) mm |
| Weight | 17.6 kg / 39lb |
| Drivers | Bass cone – 1 x 200 mm (8”) |
| High Frequency | Soft dome – 1 x 28 mm (1 ⅛”) |
| Maximum SPL | 106.5 dB continuous pink noise @ 1m LEQ 1 minute 113 dB per pair pink noise @ 1m Leq 1 minute |
| Frequency Response | 53 Hz-20 kHz ± 2 dB / 41 Hz-22kHz -6 dB |
| Connector | XLR and ¼ inch Jack combo socket |
| Impedance | 10k W electronically balanced with RF filters |
| Wiring | Pin 1 ground Sleeve |
| Pin 2 hot Tip | |
| Pin 3 cold Ring | |
| Sensitivity | -12 dBu to +6 dBu for 96 dB SPL @ 1 m set by 10 position rotary switch on rear |
| Subsonic | -3dB @ 20 Hz, 24dB/oct |
| Ultrasonic | -3dB @ 75kHz, 4dB/oct |
| Crossover | 1k40 |
| LF EQ | -2/- 4 @ 42 Hz |
| HF EQ | +/- 2dB @ 10 kHz |
| POWER AMPLIFIER | |
| LF output power | 220W RMS continuous (Note 1) |
| HF output power | 150W RMS continuous (Note 1) |
| THD | 0.025% at levels up to 1 dB below clip, 20 Hz-20 kHz. typ 0.005%@ 1kHz. |
| Hum & Noise | > -100 dB referred to clip |
| Note | The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100 mm clearance) around the amplifier heatsinks and an ambient temperature not exceeding 30ºC. |
| INDICATORS | |
| Amplifier Warming Up | Front mounted flashing green LED indicates that the amplifier is warming up to reach peak performance. |
| Normal Operation | Green LED indicates power applied and normal operation. |
| Clip | Red LED 2 dB before amplifier clip. |
| Fault Indication | Red constantly on indicates fault. |
| POWER REQUIREMENTS | |
| Voltage | Set by internal plugs: nominal 115V or 230V @ 50-60 Hz AC 230V setting: min 160V; restricted output power: max 255 AC 115V setting: min 80V; restricted output power: max 127V |
| CONSUMPTION | |
| Quiescent | 38W |
| Typical use | 100W (average music) |
| Max | 160W (average music) |
| Note | 0 dBu = 775 mV into open circuit |
