
Für die Älteren unter uns gehören diese Lautsprecher zu den ersten jugendlichen Audiowunschträumen, wie zum Beispiel das Klipschorn oder die Electro Voice Sentry III. Für alle anderen könnte dieser besondere Lautsprecher eine echte Überraschung werden.
>> Mehr erfahren>> Alle anzeigen
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: dbx 286s
Specifications | |
Type | Microphone Pre-amp Processor |
Mic Preamp Connector | XLR Floating balanced, Pin 2 Hot Mic Preamp |
Mic Preamp Input Impedance | ~4.2kΩ |
Mic Preamp gain | 0dB to +60dB |
Mic Preamp Phantom Power | +48VDC, applied to XLR pins 2 and 3 through 6.81kΩ resistors |
CMRR | >40dB, typically 55dB |
Mic Preamp max input level | 0.2Vrms, Gain = 30dB |
Mic Preamp Equivalent Input Noise (EIN) | -125dBu, 22Hz-22kHz, 150Ω source impedance |
Input Connectors | (line) Floating balanced, TIP Hot |
Input Impedance | (line) 10kΩ unbalanced, 20kΩ balanced |
Max Input | (line) >+21dBu, balanced or unbalanced |
Input Gain Range | (line) -15dB to +45 dB |
Insert Connector | 1/4" TRS: Normalled; tip is Send, ring is Return |
Insert Impedance | >5kΩ (ring-return); 100Ω (tip-send) |
Insert Max Level | >+21dBu; >+20dBm (600Ω load-tip) |
Insert Noise | <-84dBu, unweighted (20Hz-20kHz); LINE GAIN Control set to 0dB |
Insert Distortion | <0.01% THD, 20Hz-20kHz, +10dBu |
Output Connectors | 1/4" Balanced/Unbalanced TRS Connectors |
Output Impedance | 100Ω unbalanced, 200Ω balanced |
Max Output | >+21dBu, >+20dBm (600Ω load) |
Gain Adjustment Range | -30dB to +10dB |
Noise | <-80dBu unweighted (20Hz-20kHz); Both Gain Controls set for 0dB, all processing controls OFF |
Frequency Response | 20Hz to 20kHz, +0.5, -0.5dB |
THD | <0.08%THD, 20Hz-20kHz, +10dBu, all Processing Controls OFF |
Compressor Threshold Range | -40dBu to +20dBu |
Compressor Threshold Characteristic | OverEasy® |
Compressor Ratio | >4:1 For input levels beyond 20dB above threshold |
Max Compression | 30dB |
Compressor Attack Time | Program-Dependent; >1s for small level increases, down to 10ms for larage increases |
Compressor Release Time | Program-Dependent; adjustable between approximately 1dB/sec and 75dB/sec |
Compressor Distortion | Typically <0.05%THD, 20Hz-20kHz, 15dB G/R, +10dBu Output, DENSITY @ 0 |
IMD | SMPTE: <0.05%; 60Hz/7kHz 4:1, 15dB G/R, +10dBu Output Level, DENSITY @ 0 |
De-esser Characteristic | Wideband Gain Reduction |
De-esser Frequency Range | 800Hz to 10kHz High Pass, 12dB/octave |
De-esser Release Time | 12dB/octave Program-Dependent; approximately 1mS/dB |
Enhancer HF Detail Characteristic | Program-controlled shelving equalizer, approximately 15dB maximum HF boost |
Enhancer LF Detail Characteristic | Bell-shaped boost @ 80Hz, bell-shaped cut @250Hz, ratio is approximately 2:1 |
Expander/Gate Threshold Range | OFF to +15dBu |
Expander/Gate Ratio | Adjustable 1.5:1 to 10:1 |
Expander/Gate Max Depth | >50dB |
Expander/Gate Attack Time | Program-Dependent, approximately 2mS (at maximum attenuation) |
Expander/Gate Release Time | Program-Dependent, approxiamtely 10mS/dB |
Expander/Gate Dynamic Range | Typically 105dB |
Power Consumption | 15W |
Operating Voltage | DO: 120VAC 60Hz, 100VAC 50/60Hz; EU: 230VAC 50/60Hz |
Operating Temperature | 0°C to 45°C (32°F to 113°F) |
Dimensions | 1.75" x 5.75" x 19" (4.5cm x 14.6cm x 48.5cm) |
Unit Weight | 4.5 lbs/2.04 Kgs |