489_23584_2
Topthema: Träume werden wahr
Standlautsprecher · ESS AMT-1 D Revival
Für die Älteren unter uns gehören diese Lautsprecher zu den ersten jugendlichen Audiowunschträumen, wie zum Beispiel das Klipschorn oder die Electro Voice Sentry III. Für alle anderen könnte dieser besondere Lautsprecher eine echte Überraschung werden.
>> Mehr erfahren>> Alle anzeigen
487_23559_2
Topthema: Totale Eleganz
Arendal 1528 Monitor 8
Form follows function ist ja ein geflügeltes Wort für Design um die technischen Notwendigkeiten herum. Dass man aber auch beide Aspekte gleichwertig behandeln und auf die Spitze treiben kann, zeigt uns die neue Serie 1528 von Arendal.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Manley CHINOOK
Ausstattung & technische Daten
| Specification | |
| Type | PHONO STAGE |
| Gain | Internal DIP switches select 45dB or 60dB |
| Deviation from RIAA curve | Less than ± 0.5 dB from 20Hz to 20kHz at any gain setting. Typically less than ±1dB from 10Hz to 100kHz. |
| Distortion (THD+N) (47k Ohm Input Termination, 45dB gain, 1kHz sine, 0dBu output) | Typical 0.010% THD+N, into 100k Ohm load, BW = 100Hz-22kHz |
| Distortion (THD+N) (47k Ohm Input Termination, 45dB gain, 1kHz sine, 0dBu output) | Typical 0.030% THD+N, into 600 Ohm load, BW = 100Hz-22kHz |
| Dynamic Range (MM input, Gain set to 45db, 200 Ohm source) | 91dB @ 1kHz, 0.1% THD+N, BW = 22Hz-22kHz |
| Dynamic Range (MM input, Gain set to 45db, 200 Ohm source) | 107dB @ 1kHz, 1.0% THD+N, BW = 22Hz-22kHz |
| Noise Floor at 45dB gain setting with shorted input | -84 dBu, A-weighted |
| Noise Floor at 60dB gain setting with shorted input | -75 dBu, A-weighted |
| Maximum Input at 45dB gain setting with 20 Ohm Source Z @ 1kHz into 10 kOhm load | 250mV RMS = +34.5 dBu @ 1% THD+N BW=22Hz-22kHz |
| Maximum Input at 60dB gain setting with 20 Ohm Source Z @ 1kHz into 10 kOhm load | 40mV RMS = +34.2 dBu @ 1% THD+N BW=22Hz-22kHz |
| Maximum Output | +37dBu @ 1kHz, 1.5% THD+N into 100 kOhm load |
| Output Impedance | 91 Ohms |
| Minimum Recommended Load | 2500 Ohms |
| Internal Power Supply | Fully regulated linear B+, Heater, and control voltage rails. |
| Operating Mains Voltage | Units are built for original destination country |
| Power Consumption in Standby mode | 1 Watt (8.0mA @ 120VAC) |
| Power Consumption | 42 Watts (345mA @ 120VAC) |
| Mains Voltage Frequency | 50~60Hz |
| Power Transformer | Toroid contruction for low radiation. |
| Mains Fuse for 100V operation | 600mA SLO-BLO size 5mm x 20mm |
| Mains Fuse for 117V-120V operation | 800mA SLO-BLO size 5mm x 20mm |
| Mains Fuse for 220V-240V operation | 400mA SLO-BLO size 5mm x 20mm |
| Standby Transformer Fuse for all voltage operation 100V-240V | 10mA, SLO-BLO, MDL type size 1/4" x 1 1/4" |
| Badge Lamp | LED illumination |
| Dimensions | W=19", L=11", H=3 1/2" |
