501_17398_1
Anzeige
Topthema: Norddeutsche HiFi-Tage
2025 im Hotel Le Méridian Hamburg direkt an der Alster
Die Norddeutschen HiFi-Tage finden 2025 im Hotel Le Méridian Hamburg direkt an der Alster statt. Am 01.02.2025, von 10–18 Uhr und am 02.02.2025, von 10–16 Uhr können Interessierte bei freiem Eintritt durch die Vorführungen und Showrooms schlendern.
>> Mehr erfahren>> Alle anzeigen
488_23522_2
Topthema: Ingenieurskunst in Perfektion
Revelation RX2 PRO – High-End Zweikanalendstufe von Brax
Mit der RX2 PRO kündigt Brax nicht weniger als die Endstufe der Superlative an, vollgepackt mit Innovation und das erste Class-D Design der Marke.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Dynacord TGX20
Ausstattung & technische Daten
| Specification | |
| Type | DSP power amplifier 4 x 5000w, live |
| OUTPUT POWER | |
| Load impedance 2 Ω | IMD-SMPTE, 60 Hz, 7 kHz < 0.15 % |
| Maximum Output Power All channels driven: 5200 W | |
| Load impedance 2.7 Ω | Maximum Output Power All channels driven: 6000 W |
| Load impedance 4 Ω | Maximum Output Power All channels driven: 5000 W |
| Load impedance 8 Ω | Maximum Output Power All channels driven: 2500 W |
| Number of amplifier channels | 4 |
| Maximum Output Voltage | 210 V peak |
| Maximum Output Current | 84 A peak |
| AMPLIFIER | |
| Voltage Gain ref.1 kHz | 32.0 dB, adjustable 24-40 dB |
| Input Sensitivity ref. to Max. Output Voltage | 13.7 dBu (3.73 V), adjustable 5.7-21.7 dBu |
| THD 3 dB below Max., AES17, 1 kHz | < 0.05 % |
| IMD-SMPTE, 60 Hz, 7 kHz | < 0.15 % |
| DIM100, 3.15 kHz, 15 kHz | < 0.15 % |
| Crosstalk ref. 1 kHz, 12 dB below Max., 8 Ω | < -80 dB |
| Frequency Response ref. 1 kHz, analog in to speaker out | 20 Hz to 20 kHz (ą0.5 dB) |
| Damping Factor, 20 Hz to 200 Hz, 8 Ω | > 400 |
| Output Stage Topology | Class D, fixed frequency |
| Signal to Noise Ratio | A-weighted, analog input 115 dB |
| A-weighted, digital input 118 dB | |
| Output Noise | A-weighted, analog input < -70 dBu |
| A-weighted, digital input < -73 dBu | |
| DIGITAL SIGNAL PROCESSING | |
| Sampling rate | 48 kHz/96 kHz, OMNEO/Dante synchronized |
| Signal Delay/Latency | Analog in to Speaker Out, 48 kHz/96 kHz 0.70 ms/0.53 ms |
| AES3 in to Speaker Out, 48 kHz/96 kHz 1.00 ms/0.66 ms | |
| Dante Network Latency | typ. 1.00 ms |
| Signal Processing | 32/40 bit, floating point |
| User EQ | 12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type |
| User Delay | 0 to 2000 ms per channel (units: µs, ms, s,cm, m, inches, feet) |
| Array EQ | 5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass |
| Array Delay | 0 to 500 ms per channel (units: µs, ms, s, cm,m, inches, feet) |
| Speaker EQ | 10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass, & All-Pass |
| Speaker X-Over | Hi-Pass & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth,12/24/48 dB Linkwitz-Riley; AlignmentDelay, 0 to 20 ms per channel |
| Speaker FIR | up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over |
| Speaker Limiters | Peak Anticipation Limiter & RMS/TEMP Limiter per channel |
| Other functions | Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Level Meters, Impedance Measurement, & Load Monitoring |
| Memory | DSP Presets 1 Factory + 20 User |
| Speaker-Pool Presets 30 speaker settings | |
| Source Supervision & Fallback AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection | |
| CONNECTIVITY Analog Audio Input/Thru | |
| Type | 4 x 3-pin XLR female/male |
| Maximum Input Level | +24 dBu |
| Input Impedance, active balanced | 20 kΩ |
| Reference level equal to digital input | +21 dBu for 0 dBFS |
| CONNECTIVITY Digital Audio Input/Thru | |
| Type | 2 x 3-pin XLR (alternative use of Analog In/Thru) |
| Format | AES3 (AES/EBU) |
| Input Sample Rates | 32 to 192 kHz, internal Sample-Rate-Converter |
| Thru Connector | active buffered, direct bypass if device is unpowered |
| CONNECTIVITY Network | |
| Type | 2 x Neutrik etherCON/RJ45, redundant PRIMARY/SECONDARY |
| Format | 1000base-T/100base-TX, integrated switch |
| Network Audio Inputs | 8 channels, 48/96 kHz, OMNEO/Dante format |
| Network Audio Outputs (Monitor) | 2 channels, 48/96 kHz, OMNEO/Dante format |
| Front side Service Port | 1 x USB Type A |
| Mains Input | 1 x Neutrik powerCON-HC |
| Speaker Output | 4 x NL4 |
| GENERAL User Interface | |
| Display | 320 x 240 pixel, 3.5" color TFT |
| Front panel indicators | Full color LED illuminated ring |
| Front panel operating elements | Rotary encoder, Capacitive Touch Screen |
| Rear panel indicators | 2 x LED (AES3 Input mode active, Amp-Find) |
| Rear panel operating elements | Mains switch |
| Power Requirements | 100 V to 240 V, 50 Hz to 60 Hz AC |
| GENERAL Power Consumption | |
| Rated Power Consumption | 2250 W |
| ⅛ Maximum Output Power at 4 Ω | 2850 W |
| Idle Mode (no input signal) | 110 W |
| Standby Mode | < 19 W |
| Power Supply Topology | Switching Mode Power Supply with digital controlled Power Factor Correction |
| Protections | Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, In rush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Under voltage Protection |
| Cooling | Front-to-rear, temperature controlled fans, supervised |
| Ambient Temperature Limits | +5 °C to +40 °C (+40 °F to +105 °F) |
| IEC Protection Class | Class I (grounded) |
| Electromagnetical Environment | E1, E2, E3 |
| Color | Black |
| Dimensions (W x H x D), mm | 483 x 88.1 x 514.2 |
| Weight | 18.3 kg (40.4 lb) |
