Für die Älteren unter uns gehören diese Lautsprecher zu den ersten jugendlichen Audiowunschträumen, wie zum Beispiel das Klipschorn oder die Electro Voice Sentry III. Für alle anderen könnte dieser besondere Lautsprecher eine echte Überraschung werden.
>> Mehr erfahren>> Alle anzeigenVon Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: CODA Audio LINUS10
Specification | |
Type | 2 Channel DSP Amplifier with Loudspeaker Management |
General | |
Number of output channels | 2 |
Output stage | Hybrid Class H |
Internal samplerate / bit-depth | 96 kHz / 24 bit |
Output-to-noise ratio (22 Hz – 20 kHz, 4 Ω – analogue input) | >107 dB (unweighted) |
>110 dB (A-weighted) | |
Signal-to-noice ratio (22 Hz – 20 kHz, 4 Ω – digital input) | >116 dB (unweighted) |
>119 dB (A-weighted) | |
Frequency response (8 Ω load with CLEAR preset) | 20 Hz – 20 kHz = (+0.0 dB /-1.0 dB) |
THD+N & IMD (4 Ω load @ 1/2 output power) | 20 Hz – 17 kHz = < 0.01% |
Latency (input to loudspeaker output) | Minimum 2.70 ms AES/EBU input |
Minimum 2.00 ms analogue input | |
Protection circuits | Inrush current limiter Thermal limiter Output DC Output device SOA Fuse protection SMPS over-current Output overload |
LED indicators | Mute status Limit Signal Sensor Protection Ethernet control active Digital signal locked Power on Overload protection limiter Fuse protect limiter SMPS on ICL on Mains surge protection |
Ethernet connection | 2 x 100 Mbps RJ45 Control |
AC Mains | |
AC mains input connector | Neutrik 32A powerCON® |
AC mains voltage (high range) (dual voltage SMPS with automatic voltage range selection) | 180 V = Minimum |
230 V = Nominal | |
267 V = Maximum | |
AC mains voltage (low range) (dual voltage SMPS with automatic voltage range selection) | 70 V = Minimum |
120 V = Nominal | |
134 V = Maximum | |
AC mains frequency | 50 – 60 Hz |
Power consumption (1/8 power = 600 W @ 4 Ω / 2 Ω to represent typical music signal) | Amplifier in standby = 8 W |
Amplifier idle = 60 W | |
Amplifier 1/8 power = 1900 W / 4 Ω | |
Amplifier 1/8 power = 2100 W / 2 Ω | |
Input | |
Input sources | Analogue & AES/EBU |
Analogue input impedance (balanced) | 12 kΩ |
Maximum input level (analogue differential) | +21 dBu / 8.69 Vrms |
Input connections | 2x XLR3 Analogue IN |
2x XLR3 Analogue LINK | |
1x XLR5 Sensor IN | |
1x RJ45 LINET IN (8x CH) | |
1x RJ45 LINET LINK (8x CH) | |
1x AUX RJ45 | |
1x DAN RJ45 (not used) | |
Supported digital input formats (internal SRC) | 32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz / 192 kHz |
Output | |
RMS output power (20 Hz – 20 kHz, THD <0.1%) (both channels driven) | 1250 W @ 16 Ω |
2300 W @ 8 Ω | |
4000 W @ 4 Ω | |
4700 W @ 2.7 Ω | |
5100 W @ 2 Ω | |
Peak output power (20 Hz – 20 kHz, 6 dB Crest Factor) (both channels driven) | 1250 W pk @ 16 Ω |
2500 W pk @ 8 Ω | |
4900 W pk @ 4 Ω | |
6000 W pk @ 2.7 Ω | |
5300 W pk @ 2 Ω | |
Maximum output voltage | +/- 200 V pk |
Maximum output current | +/- 72 A pk |
Damping Factor (8 Ω load, 1 kHz & below) | > 400 |
Minimum output load | 2 Ω nom |
2.7 Ω for sensor control | |
Power output connections | 2x Neutrik NL4 speakON® |
Thermal | |
Operating temperature | +5°C to +55°C |
41°F to 131°F | |
Thermal output (BTU/h) | 204.9 = Idle |
1538 = 20 % | |
3415 = 50 % | |
6830 = 100 % | |
Thermal output (kWh) | 0.06 = Idle |
0.45 = 20 % | |
1000 = 50 % | |
2001 = 100 % | |
Cooling | 2x thermally controlled fans |
Hot air expelled at rear | |
Physical | |
Dimensions (WxHxD) | 483 x 88.1 x 452.5 mm / 19” x 3.5” x 17.2” (2 Rack units) |
Net Weight | 13 kg / 23.6 lbs |