390_22002_2
Topthema: Sound im Audi
Audio System RFIT Audi A6 C8 Evo2 – 20er System für Audi A6
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigen
488_23522_2
Topthema: Ingenieurskunst in Perfektion
Revelation RX2 PRO – High-End Zweikanalendstufe von Brax
Mit der RX2 PRO kündigt Brax nicht weniger als die Endstufe der Superlative an, vollgepackt mit Innovation und das erste Class-D Design der Marke.
>> Mehr erfahren>> Alle anzeigenKategorie: Verstärker Endstufen
Ausstattungsliste: Crestron AMP-221OS
Ausstattung & technische Daten
| Technische Daten | |
| Typical of 2 mono amplifier channels: | |
| Input Signal Type | Balanced or unbalanced analog line-level |
| Output Signal Type | 4/8 Ohm |
| Output Power | 120 Watts at 8 Ohms; |
| 210 Watts at 4 Ohms; | |
| Damping Factor | >100 |
| Protection | Over Current, Over/Under Voltage, Over Temperature, DC Offset |
| Frequency Response | 20Hz to 20kHz ±0.5 dB |
| THD | 0.05% @ 1kHz, full rated power at 4/8 Ohms or 8 Ohms Bridged; |
| 0.1% @ 20Hz to 20kHz, 120W at 8 Ohms;0.1% @ 20Hz to 20kHz, 120W at 8 Ohms; | |
| 0.1% @ 20Hz to 20kHz, 120W at 8 Ohms; | |
| 0.2% @ 20Hz to 20kHz, 210W at 4 Ohms; | |
| 0.1% @ 20Hz to 20kHz, 420W at 8 Ohms Bridged | |
| S/N Ratio | >103 dB, A-weighted |
| Crosstalk | >70 dB @ 1kHz |
| Gain | 23 dB with INPUT LEVEL control set at 12 o |
| Input Sensitivity | 2.22 Vrms for rated output power with INPUT LEVEL control set at 12 o |
| Input Detection Threshold | 40 mV RMS @ 1 kHz |
| Input Level Adjustment | ±10 dB from nominal |
| Connectors | |
| G | 6-32 screw, chassis ground lug |
| INPUT CH 1 – 2 | (2) 3-pin 3.5mm detachable terminal blocks; Balanced/unbalanced line-level audio inputs; Input Level: 5.3 Vrms maximum with INPUT LEVEL control set at minimum position; Input Impedance: 24k Ohms balanced, 12k Ohms unbalanced |
| SPEAKER OUTPUT CH 1 – 2 | (2) 2-pin 7.62mm 15A detachable terminal blocks; 4Ω/8Ω and 70/100V power amplifier outputs; Wire Size: Terminals accept up to 14 AWG |
| REMOTE | (1) 6-pin 3.5mm detachable terminal block; Provides (2) remote control inputs; enables independent power control of each channel via local jumpers or remote contact closures; inputs may be safely paralleled for global control |
| FUSE T6.3AH 250V | Main fuse holder; 5x20 mm, 250V, 6.3AH, time-lag, high-rupture rated |
| 100-240V~50/60Hz | (1) IEC C14 male chassis plugs, main power input; Mates with removable power cord (included) |
| Controls & Indicators | |
| PWR | (1) dual-color LED, green indicates ACTIVE state, yellow indicates STANDBY state |
| INPUT 1 – 2, SIGNAL | (2) green LEDs, indicate signal presence on each corresponding channel |
| OUTPUT 1 – 2, CLIP | (2) amber LEDs, indicate a clipping condition on each corresponding channel |
| OUTPUT 1 – 2, FAULT | (2) red LEDs; indicate over-temperature, over-current, over or under power supply voltage, or DC offset condition on each corresponding channel |
| INPUT CH 1 – 2 LEVEL (rear) | (2) Rotary input boost/attenuate adjustments w/center detent at nominal |
| ON/REMOTE/OFF (rear) | (1) 3-position slide switch; selects between all channels powered on, all channels powered off, or remote control of each individual channel |
| Power Requirements | |
| Main Power | 100-240 Volts AC, 50/60 Hz |
| Power Consumption | 62 Watts @ 8 Ohms, all channels driven at 1/8th output power; |
| 88 Watts @ 4 Ohms, all channels driven at 1/8th output power; | |
| 26 Watts, all channels idle; | |
| <1 Watt in standby | |
| Environmental | |
| Temperature | 41° to 104°F (5° to 40°C) |
| Humidity | 10% to 90% RH (non-condensing) |
| Heat Dissipation | 110 BTU/Hr @ 8 Ohms, all channels driven at 1/8th output power; |
| 121 BTU/Hr @ 4 Ohms, all channels driven at 1/8th output power; | |
| 89 BTU/Hr, all channels idle; | |
| <3.4 BTU/Hr in standby | |
| Enclosure | |
| Chassis | Metal with black finish, vented top and sides, convection cooled |
| Front Panel | Metal, black finish with polycarbonate label overlay |
| Mounting | Freestanding or 1U 19-inch rack-mountable (adhesive feet and rack ears included) |
| Dimensions | |
| Height | 1.70 in (44 mm) |
| Width | 17.28 in (439 mm); |
| 19.0 in (483 mm) with rack ears | |
| Depth | 10.34 in (263 mm) |
| Weight | 8.1 lb (3.7 kg) |
